Model NO.
PC12K
Customized
Customized
Pressure Range
-100kpa...0~10kpa...10MPa
Pressure Reference
Gauge, Absolute, Sealed Gauge
Excitation
1.5mA
Operating Temp.
-40ºC-120ºC
Input Impedance
2KΩ-5KΩ
Electrical Connection
Gold-Plated Kovar Pin or Silicon Soft Wire
Shock
100g(10ms)
Clamp and Diaphragm
316L
Pressure Port Material
304
Oil Filling
Silicon Oil
Transport Package
Standard Export Packing with Carton
Specification
Clamp diameter: 50.4mm, 64mm
Trademark
WTsensor
Origin
China
Production Capacity
50000 Pieces/Month
Type:
Piezoresistive Pressure Sensor
For:
Diffused Silicon Pressure Transmitter
Production Process:
Normal Wirewound
Material:
Stainless Steel
Measuring Medium:
All The Liquids and Gases Compatible with 316L
Certification:
RoHS
Product overview
PC12K clamp type pressure sensor adopts one-time silicon oil filling technology. The pressure felt by the diaphragm is transmitted to the pressure chip through the silicon oil, and the compensation circuit corrects the pressure signal into a linear electric signal. The clamp face diaphragm is exposed to direct pressure, which can prevent scaling, unhygienic and sticky pressure blockage and other problems. It is widely used in food, pharmaceutical, wine-making and other sanitary industries as well as occasions where the measuring medium may be fouled.
Customization is available for special structure and size of the product. The company has a mature batch production line that can complete production tasks in time with quality.
Features
Flush diaphragm with clamp structure
High reliability imported pressure chip
One-time silicon oil filling technology
Compensation board filled with glue for moisture-proof protection
All stainless steel housing
High precision and stability
Strong anti-interference and good long-term stability
18 months warranty
Applications
Medical, food industry
Environmental protection chemical coating
Polyurethane equipment
Industry standard support
Note:
(1) Calculate according to BFSL least square method.
(2) In the compensated temperature range, refer to 30ºC for 0ºC~60ºC and -10ºC~70ºC.
(3) After passing high and low temperature, return to the reference temperature.
Note: G: Gauge pressure, A: Absolute pressure, S: Sealed gauge pressure
Example: PC12K-35kGI1K1H1T0
Refer to product model PC12K, with pressure range 35kPa, gauge pressure, 1.5mA constant current excitation, 1.5" clamp, no cooling fan, and rear thread M25×1.
Ordering tips:
1 Pressure range can be selected higher or lower than actual conditions but should be within ±30%FS.
2 Pressure reference consists of gauge pressure, absolute pressure and sealed gauge pressure.
4 The commonly used compensation of the product is 1.5mA constant current compensation. Suggest selecting the option with priority.
5 The material and process for manufacturing negative pressure sensors are different from those of positive pressure sensors. So gauge pressure sensors cannot be used as substitute of negative pressure sensors.
6 For special requirements on performance parameters and functions of the product, please contact us.
About US:
Exhibitions:
Certifications:
PC12K clamp type pressure sensor adopts one-time silicon oil filling technology. The pressure felt by the diaphragm is transmitted to the pressure chip through the silicon oil, and the compensation circuit corrects the pressure signal into a linear electric signal. The clamp face diaphragm is exposed to direct pressure, which can prevent scaling, unhygienic and sticky pressure blockage and other problems. It is widely used in food, pharmaceutical, wine-making and other sanitary industries as well as occasions where the measuring medium may be fouled.
Customization is available for special structure and size of the product. The company has a mature batch production line that can complete production tasks in time with quality.
Features
Flush diaphragm with clamp structure
High reliability imported pressure chip
One-time silicon oil filling technology
Compensation board filled with glue for moisture-proof protection
All stainless steel housing
High precision and stability
Strong anti-interference and good long-term stability
18 months warranty
Applications
Medical, food industry
Environmental protection chemical coating
Polyurethane equipment
Industry standard support
| Electrical performance parameters | |
| Pressure range | -100kPa~0~10kPa…10MPa |
| Pressure reference | Gauge pressure, Absolute pressure, Sealed gauge pressure |
| Excitation | 1.5mA recommended for constant current |
| Input impedance | Constant current: 2kΩ~5kΩ |
| Electrical connection | Gold-plated KOVAR pin or silicon soft wire |
| Compensated temp. | Constant current: 0ºC~60ºC(≤70kPa); -10ºC~70ºC(Other ranges) |
| Operating temp. | -40ºC~120ºC |
| Storage temp. | -40ºC~120ºC |
| Insulation resistance | ≥200MΩ/250VDC |
| Response time | ≤1ms(Up to 90%FS) |
| Measuring medium | All the liquids and gases compatible with 316L. |
| Mechanical vibration | 20g(20~5000HZ) |
| Shock | 100g(10ms) |
| Service life | 10×106(cycles) |
| Structural performance parameters | |
| Diaphragm material | 316L |
| Clamp material | 316L |
| Pressure port material | 304 |
| Filling oil | Silicon oil |
| Basic parameters | ||||||
| Item | Condition | Min | Nominal | Max | Unit | Note |
| Nonlinearity | -0.3 | ±0.25 | 0.3 | %FS | Note(1) | |
| Hysteresis | -0.05 | ±0.03 | 0.05 | %FS | ||
| Repeatability | -0.05 | ±0.03 | 0.05 | %FS | ||
| Zero output | -2 | ±1 | 2 | mV | ||
| Full scale span output | 10kPa Other ranges | 30 60 | 90 | 150 | mV | 1.5mA excitation |
| Zero temp. coefficient | 10kPa Other ranges | -2 -1.5 | ±1.5 ±0.75 | 2 1.5 | %FS | Note(2) |
| Span temp. coefficient | -1.5 | ±0.75 | 1.5 | %FS | Note(2) | |
| Thermal hysteresis | -0.075 | ±0.05 | 0.075 | %FS | Note(3) | |
| Long term stability | -0.3 | ±0.2 | 0.3 | %FS/Year | ||
(1) Calculate according to BFSL least square method.
(2) In the compensated temperature range, refer to 30ºC for 0ºC~60ºC and -10ºC~70ºC.
(3) After passing high and low temperature, return to the reference temperature.
| Structure and dimensions |
| Pressure range selection | ||||
| Code | Pressure reference | Pressure range | Overpressure | Burst pressure |
| 10k | G | 0~10kPa | 300%FS | 600%FS |
| 20k | G | 0~20kPa | 300%FS | 600%FS |
| 35k | G | 0~35kPa | 300%FS | 600%FS |
| 70k | G | 0~70kPa | 300%FS | 600%FS |
| 100k | G, A | 0~100kPa | 200%FS | 500%FS |
| 160k | G, A | 0~160kPa | 200%FS | 500%FS |
| 250k | G, A | 0~250kPa | 200%FS | 500%FS |
| 400k | G | 0~400kPa | 200%FS | 500%FS |
| 600k | G | 0~600kPa | 200%FS | 500%FS |
| 1M | G | 0~1MPa | 200%FS | 500%FS |
| 1.6M | G, S | 0~1.6MPa | 200%FS | 500%FS |
| 2.5M | G, S | 0~2.5MPa | 200%FS | 500%FS |
| 4M | S | 0~4MPa | 200%FS | 400%FS |
| 6M | S | 0~6MPa | 200%FS | 400%FS |
| 10M | S | 0~10MPa | 200%FS | 400%FS |
| N5k | Omitted | -100~250kPa | 750kPa | 1.25MPa |
| N7k | Omitted | -100~600kPa | 1.2MPa | 3MPa |
| N8M | Omitted | -0.1~1MPa | 2MPa | 5MPa |
| N9M | Omitted | -0.1~1.6MPa | 3MPa | 9MPa |
| N10M | Omitted | -0.1~2.5MPa | 5MPa | 12.5MPa |
| How to order |
Example: PC12K-35kGI1K1H1T0
Refer to product model PC12K, with pressure range 35kPa, gauge pressure, 1.5mA constant current excitation, 1.5" clamp, no cooling fan, and rear thread M25×1.
Ordering tips:
1 Pressure range can be selected higher or lower than actual conditions but should be within ±30%FS.
2 Pressure reference consists of gauge pressure, absolute pressure and sealed gauge pressure.
- Gauge pressure is based on the current atmospheric pressure. Generally, it refers to the measurement of pressure which is greater than the current atmospheric pressure. Negative pressure is a special case of gauge pressure. It refers that there is such working condition that the pressure of work site is lower than the current atmospheric pressure.
- Absolute pressure is based on vacuum.
- As for sealed gauge pressure, PC10 uses absolute pressure die for gauge pressure product based on the atmospheric pressure of production site. For pressure range above 6MPa, gauge pressure cannot be selected, but only sealed gauge pressure.
4 The commonly used compensation of the product is 1.5mA constant current compensation. Suggest selecting the option with priority.
5 The material and process for manufacturing negative pressure sensors are different from those of positive pressure sensors. So gauge pressure sensors cannot be used as substitute of negative pressure sensors.
6 For special requirements on performance parameters and functions of the product, please contact us.
About US:
Exhibitions:
Certifications:
Send Message
